Chinese Version
Home About Us News Products Service Support Shop trading partners  
 
The Omnibus Infrared Remote
All-round remote controller
Versatile Battery
accessory
 
 
 
 

All kind mode and control button command table

M Mode
B Mode
C1 Mode
C2 Mode
C3 Mode

Mode / Confirm

Choose other mode Choose other mode / Confirm (Judge setting value)

Mode setting start / left button

No action

Setting start button / Move to the left

Right button No action Move to the right
Number button / Shutter value left button No action Number cycle jumping selection

When the number cycle jumping select the shutter (TV) setting, moving same direction

Clear /
Shutter value right button

Clear the signal emission received setting Clear the signal emission received setting

When clear the signal emission received setting for the number cycle of shutter (TV) setting, reverse moving

 

Display mode

Displaying :

M General mode
(screen starting pre-setting value)
B mode - Slow-Shutter Speeds & Timer

C1- Intermittent operation by freqency

C2-Intermittent counting time mode

C3-Reserve taking picture mode

TIMER

Timer display

Display method ¡G (0 hour ¡G 00 minute ¡G 00 second of pre-setting value)
M mode ¡V No display
B mode ¡V display the taking time (positive number), or setting the time (Inverse)
C1 ¡B C2 ¡B C3 mode- Intermittent time value (Fixed value)
¡° Maximum setting is 9 hours 59 minutes and 59 seconds


TV Shutter value display

¡° This is not the camera shutter and is the setting value for protecting the shutter time inaccuracy
M, B mode --- No display
C1 ¡B C2 ¡B C3 mode---- display, can setting
Display method ¡G (1)AUTO no matter camera shutter speed (this is the pre-setting value)
(2) 4000 ~ 2 mean 1/4000 ~ 1/2 second
(3) 1 ¡¨ ~ 30 ¡¨ mean 1 ¬í ~ 30second
Total 29 displays. If there is no same shutter value, you may select the closest shutter value

NUMBER of frequency display

Display method ¡G (000 is pre-setting value) M ¡B B mode---- No display
C1 ¡B C2 ¡B C3 mode---- can set the shoot frequency
Minimum setting is 001(one time) *If setting 000 will appear error
Maximum setting is 999 *Multi setting making enough power

CLOCK

Time display

Display method ¡G (00 hours ¡G 00 minute) M, B mode ---- No display
C1 mode ¡V Start shoot ¡A display the total shoot time( positive time counting)
C2 mode ¡V display the setting of shoot time counting (inverse time counting)
C3 mode ¡V display pre-setting time (inverse time counting), after shoot , it will display the total shoot time (positive time counting)
Minimum setting is 00 ¡G 01(one minute)* if setting 00 ¡G 00, it will appear error
Maximum setting is 99 hours and 59 minutes *long time setting must confirm having sufficient power

Focus display

when focusing, it will launch information or display circuit situation.

shoot
/ Confirm display

(1) M, B mode (No setting), it only displays the signal emission or circuit opening during taking photo
(2) B (Have setting), C1, C2, C3, it regards (SURE) key of displaying symbol. It is also displayed the signal emission or circuit opening for the shutter button during shoot..

Low battery display

Voltage value is setting below 2.4V, it will appear the low battery label
¡° Low battery display will not cut the power down, it will depend on the battery status. Be careful the display for long time shoot .
¡° Do not use the re-chargeable battery. The voltage is around 2.4V, and it easily causes insufficient effort of the crystal as well as shutting down.

¡ýCharacters¡ýIntroduction¡ýspecification¡ýGuide¡ýHome¡ý